Coremo Brakes
Coremo Brakes
Range of product selections by Coremo Brakes:
Coremo Brakes - Pneumatic Caliper Brakes
Coremo Brakes - Air Applied, Spring Release Caliper Brakes (Positive Brakes)
Type ‘Micro’
Type ‘MPA’
Type ‘A’
Type ‘B’
Type ‘C’
Type ‘D’
Type ‘E’
Type ‘F’
Type ‘G’
Coremo Brakes - Spring Applied, Air Release Caliper Brakes (Negative or Fail-Safe Brakes)
Type ‘MPA-N’
Type ‘A-N’
Type ‘B-N’
Type ‘D-N’
Type ‘EL-N’
Type ‘F-N’
Type ‘G-N’
Coremo Brakes - Dual Combination Pneumatic Caliper Brake function
Coremo – Dual Combination Pneumatic Caliper Brake function as both a Positive and Negative Brake. It comprises a single thruster and is designed in which the clamping forces are either applied by the air (air-actuated) or the springs (failsafe). This is suitable for applications which require both continuous and emergency braking simultaneously. The advantage of just one Caliper Brake instead of two.
Type ‘A-Dual’
Type ‘D-Dual’
Type ‘F-Dual’
Type ‘G-Dual’
Coremo – Hydraulic Brakes
Coremo – Pneumatic Caliper Brakes are designed for applications which use air pressure to operate the braking system. All Coremo Caliper brakes can be fitted with a wear indicator and an on/off indicator device to protect the system during operation. The brake can be installed in any position since it has a lever balancing and lining pad alignment system (depending on type).
Hydraulic Applied, Spring Release Brake (Positive Brake)
Hydraulic Applied, Spring Release Brake (Positive Brake) are normally for Service Stops (Stopping). Forces vary depending on the pressure of the supplied Hydraulic pressure (up to a maximum pressure of 200 bar).
Type ‘A3-ID’
Type ‘D3-ID’
Type ‘F3-ID’
Type ‘G3-ID’
Type ‘ID800’
Type ‘ID900’
Type ‘ID2000’
Type ‘ID3000’
Spring Applied, Hydraulic Release Brake (Negative or Fail-Safe Brake)
Coremo – Spring Applied, Hydraulic Release Brake (Negative or Fail-Safe Brake) are chosen for Emergency and/or Parking Brake (Holding) functions. The clamping force of each model is generated by helical springs which allow low reaction times and release by Hydraulic Pressure (up to a maximum pressure of 200 bar).
Type ‘AN-ID’
Type ‘DN-IN’
Type ‘EN-ID’
Type ‘FN-ID’
Type ‘GN-ID’
Type ‘ID800-N’
Type ‘ID900-N’
Type ‘ID1500-N’
Type ‘ID2000-N’
Type ‘ID2500-N’
Type ‘ID3000-N’
Coremo Brakes - Mechanical Caliper Brakes
Coremo – Mechanical Caliper Brakes are intended for applications where pneumatic or hydraulic power are not available, making mechanical operation of the brake necessary. The brake can be installed in any position since it has a lever balancing and lining pad alignment system (depending on type).
Mechanically Applied Caliper Brake, forces are applied by hand by turning the handwheel a specific number of turns to obtain the required torques.
Type ‘MPA-M’
Type ‘A-M’
Type ‘B-M’
Type ‘D-M’
Type ‘E-M’
Type ‘F-M’
Type ‘G-M’
Coremo Brakes - Electric, Fail Safe Caliper Brakes
failsafe electric brakes are designed for applications where pneumatic or hydraulic power is not available and a remote actuation is required.
Coremo – Electric, Fail Safe Caliper Brake, operates on voltage of 110 or 220 and is rated at IP 55
Type ‘D-E’
Coremo Brakes - Hydraulic Power Pack
Coremo – Hydraulic Power Pack are designed to complete the braking system of hydraulic brake. Two different families have been designed: “P” for Hydraulic Oil-applied Brakes and “N” for Spring-Applied, Hydraulic Release Brakes.
HPU-P
HPU-N
Coremo – Air Cooled and Fan Cooled Brakes
Coremo – Air Cooled and Fan Cooled Brakes are small Caliper Brake that can be designed mainly for Roll to Roll applications as the Slip or Tension brake where tensioning of the web is crucial. Coremo – Air Cooled Brake, air applied brakes. Type ‘MAC’ and ‘AC’ have rotating disc that cast with ‘fins’ for cooling during operation. Modulo Brakes can be fitted with Fan to aid in the cooling.
Type ‘MAC
Type ‘AC’
Type ‘SB’
Type ‘TB’
Type ‘Modulo’
Coremo Brakes - Mini Clutch and Brake
Coremo – Mini Clutch and Brake were developed for applications with limited space. Coremo – Mini Clutch and Brake, small ‘envelope’ form is suitable for application with limited space. CAB and SMART type are designed for single face braking.
Type ‘CL 2-3’ Type ‘CLF 2-3’
Type ‘CL 4-5’ Type ‘CLF 4-5’ Type ‘BL’
Type ‘AP’ Type ‘APA’
Type ‘BLM’
Type ‘CAB’
Type ‘SMART’
Coremo Brakes - Air Tube Design Clutch and Brakes
Coremo – Air Tube Design Clutch and Brakes are Low Inertia, Pneumatic Clutch and Brake.
Type ‘M’ Brake
Type ‘BI’ Brake
Type ‘BI’ Clutch
Type ‘VS’ Clutch
Coremo Brakes - Water Cooled Clutch and Brake
Coremo – Water Cooled Clutch and Brake, are used in applications where constant slippage is require. The Water Cooling Jackets in the Brakes helps to ‘carry’ away the heat generated. Coremo has either Steel or Copper Plates for the Cooling Jackets.
Type ‘W’ or ‘R’ Brake
Type ‘W’ or ‘R’ Clutch
Coremo Brakes - GEMELL (Clutch Brake Combination)
Coremo – GEMELL (Clutch Brake Combination), with Spring Applied Brake and Air Applied Clutch, this Combination is perfect for applications where Clutch Brake operations are fast and frequent. Metal Forming, Press and Stamping are some examples of application
Type ‘AF’
Type ‘AF OC’
Type ‘OC”
Type ‘LL’
Contact Us
Talk to Us
Not too sure which product is suitable for your equipment?
